标题: A Visit to a German Electroplating Shop Reveals an Approach to 3D Printed AI Cooling Plates [打印本页] 作者: admin 时间: 2026-11-17 20:09 标题: A Visit to a German Electroplating Shop Reveals an Approach to 3D Printed AI Cooling Plates In November 2026, during Germany's Formnext show, a local Chinese student who follows Nanjixiong guided us through forests in autumn color and villages surrounded by broad meadows. We drove into the hills near Bonn to visit a factory that has worked in electrochemical deposition for more than 30 years.
(, 下载次数: 0)
上传
点击文件名下载附件
The scenery along the way was beautiful.
There were no giant workshops or automated guided vehicles moving along production lines. Galvano-T's founder and the second-generation successor greeted us.
(, 下载次数: 0)
上传
点击文件名下载附件
The father and daughter discussed process details and engineering decisions, then showed us their tanks, mandrels and coated samples. The underlying principle is straightforward. The value lies in process and detail control.
(, 下载次数: 0)
上传
点击文件名下载附件
The small workshop has worked on advanced applications such as copper coatings inside rocket combustion chambers and pure copper coatings for particle accelerator radio-frequency cavities. We were especially interested in whether its three decades of deposition experience could help China's growing AI chip cooling and commercial space manufacturing industries.
Electroforming in a small workshop
Galvano-T's core process is Galvanoformung, or electroforming. The founder showed us how deposition can grow a tube on a precision mandrel when machining reaches its limits below a 0.5 mm wall thickness. Even grooves inside hollow waveguides can be formed as part of the same piece.
(, 下载次数: 0)
上传
点击文件名下载附件
For thermal management, electrochemical deposition gives designers substantial freedom over cooling-channel geometry. Typical deposit thicknesses are 0.1–10 mm. Parts can operate under high vacuum, with a reported leak rate below 10 mbar·L/s. The entire process occurs at room temperature without adding heat or changing the substrate's mechanical properties.
These properties address difficulties making complex internal cavities. The shop's expertise comes from more than 30 years of hands-on experience with bath control, current distribution and mandrels.
Applying the technique to chip cooling
In the 2026 AI computing race, rack power density has climbed to 30–40 kW, making direct-to-chip liquid cooling a necessity. Conventional microchannel cold plates face structural limitations: narrow channels raise pumping power and produce uneven temperatures across the chip surface.
(, 下载次数: 0)
上传
点击文件名下载附件
Greater freedom in channel design offers a way forward. Researchers at National Yang Ming Chiao Tung University and the University of Texas recently reported the DINOS-CP cold plate. It uses electrochemical additive manufacturing (ECAM) to form complex fine channels and micro pin fins as one piece. The paper states that conventional CNC and metal 3D printing struggle to achieve equivalent precision and surface quality.
Research by the University of Illinois and Fabric8Labs reported that a topology-optimized pure copper cold plate made with ECAM had 32% lower thermal resistance and 68% lower pressure drop than a conventional design. Hongwu Song's team at the Institute of Metal Research, Chinese Academy of Sciences, showed that deposition could form graded porous copper wicks inside narrow grooves, doubling single-tube heat dissipation compared with a straight-groove tube.
(, 下载次数: 0)
上传
点击文件名下载附件
Two Bambu Lab 3D printers in the founder's office make shop jigs, fixtures and even electroforming molds.
Galvano-T's process capabilities match many of these requirements. Its ability to electroform cooling channels fits the engineering work needed to take ECAM cold plates from lab samples into production.
Commercial rocket chambers and a combined manufacturing route
Copper alloys are commonly used to line commercial rocket combustion chambers, where operating temperatures can reach 3,000–4,000°C. Electroforming was used in the Vulcain engine for Ariane 5, but the traditional process is complex and measured in months.
Selective laser melting or laser powder bed fusion (SLM/L-PBF) can form complex cooling channels as part of a single build, cutting lead times to weeks or days. As-printed copper alloy still needs finishing to address surface roughness and manage internal defects.
(, 下载次数: 0)
上传
点击文件名下载附件
One hybrid approach combines a printed structure and internal passage geometry with an electrochemically deposited, dense and thermally conductive pure copper surface to improve finish.
(, 下载次数: 0)
上传
点击文件名下载附件
Galvano-T has demonstrated copper plating in particle accelerator hardware. In a March 2026 study on a radio-frequency quadrupole (RFQ) cavity, researchers used multimaterial laser powder bed fusion to make a CuCr1Zr cavity integrated with a tool steel shell. Galvano-T plated the interior with pure copper at a thickness of 50 ± 10 μm. The article draws a parallel between surface finishing of these complex cavities and commercial rocket chamber liners.
(, 下载次数: 0)
上传
点击文件名下载附件
Taking the process into production
The shop's expertise includes bath maintenance, how current density changes with geometry, mandrel design and managing residual stress in coatings. Buying a machine cannot easily reproduce three decades of accumulated knowledge.
China already has demand for these processes in AI chip cooling and commercial spaceflight. The gap is in taking electrochemical deposition from lab validation into production.
(, 下载次数: 0)
上传
点击文件名下载附件
Electrochemical deposition on the inside of a large copper component.
A practical path would combine the German shop's process knowledge and controls with China's established 3D printing capabilities. Printing can produce complex channels and lightweight structures, while deposition controls copper purity, density and surface quality. Cold plate micro pin fins and internal surfaces for commercial aerospace cooling pose related manufacturing challenges.
Thirty years ago, the shop made seamless copper tubes with electroforming. Today, the same technique could help cool an AI chip. Nanjixiong hopes Chinese manufacturers can put this combination of established expertise and newer manufacturing technology into practice.
AI-translated from an article by Xiaoruanxiong on Nanjixiong, originally published on 2026-11-17. Text and images retain the original source attribution. Read the original Chinese article
欢迎光临 All Voice of China 3D Printing (https://www.panda3dp.com/)